Why Understanding Essential Plumbing Skills is Essential When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Essential When Installing a Bathtub
Blog Article
We've stumbled on this article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and think it made sense to discuss it with you over here.
Installing a bathtub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is readily easily accessible, the task can relocate quickly; if you have to open a wall to remove the old tub and also place the new bathtub, the job is much harder. In either situation, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Rather than employing a professional to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This short article will aid you set up a new bath tub in your washroom if you have already purchased a brand-new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools and material list should comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the restricted gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the tub up until the level reviews level.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet and also the typical electrical outlet for leakages.
Lastly, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait till the bathtub has been utilized at the very least when as this will certainly settle it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Protect the faucet in position with the supplier supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall between the bath and also the tiling, causing problems with wetness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and installations. They are sold in tubes and cartridges, as well as can securing spaces up to a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub remains in usage. The sealant can fracture rather very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is a good idea to fit the tiles making use of waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on Tools You Need to Install a New Bathtub ? Make a remark directly below. We'd be interested to hear your thinking about this blog entry. Hoping to see you back again later on. Don't hesitate to take a moment to distribute this blog entry if you enjoyed it. Thanks a lot for your time. Kindly visit our blog back soon.
Reliable help? Dial. Report this page